Skip to content
Let ideas be heard and improvements last.
Gemy

How OEE is calculated and how it is misused

In brief

OEE is the product of three rates: availability, performance and quality. The calculation is simple; the misuse is widespread. The formula, the six big losses and how not to turn OEE into a tool of punishment.

5 November 2026 · 5 min read

Sample company · demo dataScorecards: indicators and target values
Scorecards

Overall equipment effectiveness (OEE) tells how much of a machine's or line's planned production time was spent making good parts. The Lean Enterprise Institute lexicon defines OEE as the equipment utilisation measure of total productive maintenance and calculates it as the product of three rates: availability, performance and quality. ISO 22400-2 is the international standard that defines key performance indicators for manufacturing operations management, and OEE is among those indicators. The calculation is simple; the traps are not in the arithmetic but in the interpretation.

The three rates

  • Availability: run time divided by planned production time. Planned production time is the shift time minus planned stops such as breaks and planned maintenance; run time is that minus breakdowns, unplanned stops, setup and adjustment.
  • Performance: ideal cycle time times total output, divided by run time. If the machine runs slower than it should or stops briefly and often, this rate falls.
  • Quality: good parts divided by total output. Scrap and reworked parts do not count as good parts.

OEE is the product of these three rates. Because it is a product, each rate shrinks the others: with all three at ninety percent, OEE is just above seventy. That is the first thing to know so as not to be surprised by how small the number looks.

The six big losses

The Lean Enterprise Institute lexicon ties the six big losses to the three rates: failures and adjustments lower availability, minor stoppages and reduced speed lower performance, scrap and rework lower quality. The TPM page of the US Environmental Protection Agency gives a similar list of losses and notes that minor stoppages are hard to record by hand and often do not appear in reports; that is the loss OEE hides most.

Misuse one: measuring people

OEE is a measure of the equipment, not of the operator. Breakdowns, a wrong ideal cycle time, missing material and unplanned order changes are not in the operator's hands. When OEE is turned into an operator ranking two things happen: stops go unrecorded and minor stoppages are never written down. The number rises, the loss carries on unchanged.

Misuse two: a single target number

It is often said that there is a world-class OEE value; but every line has a different product mix, cycle time and changeover frequency. The meaningful comparison is of the same line against its own history. Comparison between lines says something only when the same loss definitions are used.

Misuse three: averaging the rates

A week's OEE is not the average of the daily OEEs. The correct calculation sums the times and quantities and recomputes the rate; otherwise a short shift's high rate hides a long shift's loss. Likewise, a wrongly entered ideal cycle time pushes performance above one hundred percent; that is not an achievement but a data error.

Using OEE well

  • Record loss reasons with a two-level tree: main reason and sub-reason. Without sub-reasons there is no Pareto.
  • Find the biggest loss with a Pareto chart and make it the topic of a focused improvement project. OEE's job ends there; the rest is kaizen.
  • Set the target per line and treat every shift below target as a task; hanging the number on the wall is not a task.
  • Count minor stoppages separately; a loss that does not appear in reports never gets solved.
  • Verify the ideal cycle time on the floor: is it the machine's design speed or the best speed achievable today? Whichever is chosen, the same rule applies on every line; otherwise the performance rate cannot be compared between lines.
  • Keep the list of planned stops in writing: breaks, planned maintenance and no-schedule time are deducted from planned production time; if this list changes, OEE changes too and comparison with the past breaks down.
Sample company · demo dataYamazumi chart: station loads and the takt line
Yamazumi chart

How it is done in Gemy

  • If the OEE feature is on, a record is entered per line, day and shift: total output, scrap, rework, the start-up share and stops with reason and minutes. Stop reasons form a two-level tree; a reason that has sub-reasons cannot be chosen directly.
  • Availability, performance, quality and OEE are calculated; under every figure the calculation is written with the real values. If performance exceeds one hundred percent it is capped at one hundred and a warning is shown.
  • When days, weeks, months or lines are aggregated, rates are not averaged; times and quantities are summed and the rate is recomputed. A minor stoppage is a separate line as a performance loss.
  • The line page shows the trend, the six big losses and the loss Pareto; the overview has a line comparison. There is no ranking of people and the name of whoever entered the record does not appear in reports.
  • If a record's OEE is below target, an improvement task is opened and goes to the manager of the line's unit. Entry is by hand or Excel; there is no machine connection. The company switches it on.

In short

OEE is the product of availability, performance and quality and exists to make the six big losses visible. Its misuses are clear: measuring people, tying it to a single universal target and averaging the rates. Its correct use is recording losses down to the sub-reason, finding the biggest with a Pareto and making it an improvement topic. OEE is not a report card but a compass.

Sources

You may copy and share this article with attribution (Gemy, https://www.gemydigital.com/en/blog/oee-nasil-hesaplanir-ve-nasil-yanlis-kullanilir).

Related posts

Cookies

Essential cookies are needed for the site to work. Analytics cookies load only if you allow them; declining is as easy as accepting. You can change your choice at any time via the footer link.

Cookie policyPrivacy notice