Skip to content
Let ideas be heard and improvements last.
Gemy

Health, Safety, Environment and Sustainability

LOTO: isolating and locking out energy

Before maintenance or cleaning, isolating all of a machine's energy sources, locking them out, releasing stored energy and testing for zero energy.

Level:
Practitioner
Who it is for:
Safety specialist, Maintenance and calibration lead, Shift supervisor

Definition

LOTO, short for lockout tagout, is the method that stops a machine from starting unexpectedly during maintenance or cleaning. The energy sources are isolated with an energy isolating device, and a lock and a tag are put on the device. The energy may be electrical, mechanical, hydraulic, pneumatic, chemical or thermal; the weight of a raised part and a tensioned spring are stored energy too. The lock holds the device in the off position; the tag warns everyone not to operate it.

Lockout tagout (LOTO)

When does it help?

  • Maintenance, cleaning or clearing a jam is done with a machine guard open.
  • Besides electricity, the machine also has compressed air, hydraulics or another energy source.
  • Several people will work on the same machine at the same time.

When does it not help?

  • Treating a push button stop or a selector switch as isolation; in OSHA's definition these are not energy isolating devices.
  • Replacing a permit to work in high-risk maintenance; HSE says some jobs need a formal system of work such as a permit to work.

Step-by-step method

  1. Prepare

    Before you start, learn the type, size and hazard of the energy and how it is isolated.

  2. Shut the machine down

    Stop the machine in an orderly way by its own shutdown method and tell the people affected.

  3. Isolate the energy

    Operate the isolating device of every energy source; switching off the control circuit is not enough.

  4. Apply the lock and the tag

    The person doing the job puts their own lock and tag on each isolating device.

  5. Release stored energy

    Release compressed air and hydraulic pressure; hold parts that could fall with a block or a mechanical support. If energy can build up again, keep checking until the job is finished.

  6. Test for zero energy

    Before starting work, use the start control to test that the machine does not run; after the test, put the control back to off.

  7. Remove the lock safely

    Check the area and the tools, clear people away and tell them; the person who applied the lock removes it.

Example scenario

Example scenario

Locking out during press maintenance

In a press shop the maintenance team is about to replace a sensor under the die. The operator has stopped the press with a button, but that is not isolation. The maintenance lead switches off and locks the isolator in the panel, supports the ram with a safety block and releases the hydraulic pressure. A test with the start button shows the press does not run; the control goes back to off, then both technicians fit their own locks.

A fictional example; the people, company and numbers are not real.

Common mistakes

  • Stopping the machine with a button or an emergency stop and treating it as isolated; the control circuit does not cut the energy.
  • Skipping the verification step; the wrong isolator may have been switched off, and only a test shows it.
  • Forgetting stored energy; compressed air, hydraulic pressure or the weight of a raised part can move the machine even with the power off.
  • Leaving the control on after the test; once the lock is removed and energy returns, the machine can start by itself.
  • Working with a single lock on a group job; if each person does not apply their own lock, whoever finishes first may remove it.

Terms

Sources

  1. 29 CFR 1910.147 The control of hazardous energy (lockout/tagout), Occupational Safety and Health Administration (OSHA) (accessed 16 November 2026)
  2. Control of Hazardous Energy (Lockout/Tagout), Overview, Occupational Safety and Health Administration (OSHA) (accessed 16 November 2026)
  3. Maintenance of work equipment, Health and Safety Executive (HSE) (accessed 16 November 2026)

Cookies

Essential cookies are needed for the site to work. Analytics cookies load only if you allow them; declining is as easy as accepting. You can change your choice at any time via the footer link.

Cookie policyPrivacy notice